View PSPRL9802D_4195987.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PSPRL9802D Series
Active PFC 200 Watt Dual Output AC/DC Switching Power Supply FEATURES
2 Year Warranty Optional Top Cover 90 ~ 264VAC Universal AC Input Approved to UL CUL TUV CE and CB Power Factor Corrected to EN61000-3-2 Class D 5V/ 12V/ 24V Dual Output Optional Combinations Compact 1U Size & Power Density: 5.2 Watts/cu in. Convection-Cooled and with Forced Air Cooling Rating Options
SPECIFICATIONS: PSPRL9802D Series
All specifications are based on 25 C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. INPUT SPECIFICATIONS Input Voltage 90 - 264VAC Full Range Input Frequency 47 to 63Hz Input Current 4A at 100VAC full load Inrush Current 35A max @ 110VAC with full load and cold start. Leakage Current 1.5mA max @ 240VAC Remote ON/OFF Designated as REMO on the CN3, requires a low signal to inhibit output. Hiccup mode. OUTPUT SPECIFICATIONS Output Voltage See Table Output Power Range 200 Watts max. Output Adjustability Output user adjustable 5% minimum. Total Regulation 5% Output Current See Table Ripple & Noise (peak to peak) 1% Transient Response Output voltage returns to within 1% in less than 500s for a 50% dynamic load peak does not excess 5%. Hold-Up Time 20ms min. at 80% of full load. Overshoot Turn-on/off not exceed 5% over nominal voltage. Turn On Delay 1 second maximum at 120VAC. PROTECTION Over Voltage Protection Latching down will occur when output voltage exceeds 130% and recycle AC input to reset. Short Circuit Protection Trip without damage and auto-recovery. Over-Temperature Protection Protected in the event of excessive operating ambient 85C and automatic recovery. Over-Power Protection Hiccup mode 110-140%; auto-recovery. Input Circuit Protection A protected 250V/5A fuse inserted. GENERAL SPECIFICATIONS Efficiency 75% minimum (Measuring at 230Vand full load). 1500 VAC input line to chassis (10mA DC cut off current, isolating 3000VAC primary to secondary Withstand Voltage windings. Primary to core 1500VAC. All for 3 seconds. Burn In 45 5C for one hour @ 230VAC with full load. PFC Active power factor correction meets EN61000-3-2 class D. Designated as PG on the CN3 will go high 100-500ms after regulation and goes low 1ms before loss of Power Good regulation. Power Supply On Green LED designated as LED 1 on the PCB. Grounding Test Apply 25A from ground pin of the three-prong plug to the far most earth. Max allowable resistance 0.1 ohm.
o
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797
PSPRL9802D Series
Active PFC 200 Watt Dual Output AC/DC Switching Power Supply
SPECIFICATIONS (CONTINUED)
ENVIRONMENTAL SPECIFICATIONS Operating Temperature Storage Temperature Operating Humidity Storage Humidity Vibration Cooling Fan Drive MTBF PHYSICAL SPECIFICATIONS Weight Dimensions Warranty SAFETY Emissions Safety Regulations 0C to +70C ambient, de-rating at 2.5% per degree from 50C to 70C. -20C to +85C 5% to 90% RH, non-condensing 5% to 95% RH, non-condensing Frequency 5 ~ 50Hz, acceleration 7.35 m/(s x s) on X, Y, and Z axis. 200W max. with 17CFM airflow or 150W max. convection. 12VDC/300mA is available to drive an external fan. 100,000 hours (according to MIL-HBK-217F) at 30C. 650 grams max. 6.8(L) x 3.8(W) x 1.5(H) inches U-case 2 years FCC part15, CISPR 22 Class B, Conducted. Approved to UL60950-1, CSA C22.2 No. 60950-1-03, TUV EN60950-1, CE Mark (LVD) EN61000-3-2,3, and IEC61000-4 Series Regulations and CB.
OUTPUT VOLTAGE / CURRENT RATING CHART
Model PSPRL9802Dx-0512 PSPRL9802Dx-0524 PSPRL9802Dx-1224 Output Voltage Range V1: +5 VDC V2: +12 VDC V1: +5 VDC V2: +24 VDC V1: +12 VDC V2: +24 VDC Output Current Regulation Max Load Max. Load (17CFM) (Convection) 25A 15A 5% 12.5A 10A 5% 25A 15A 5% 6.25A 5A 5% 16.66A 12.5A 5% 8.3A 6.25A 5% Ripple & Noise 1% 1% 1% 1% 1% 1%
NOTES
1. PSPRL9802D Series is designated as PSPRL9802Dx-y where x can be blank (U-chassis) or C (U-chassis with top cover), y can be 0512, 0524, 1224 for output voltage. 2. Total combined power of V1 and V2 not to exceed 200W with 17CFM forced air and 150W convection cooling for all models. 3. 10% minimum load is required for all outputs to maintain the ripple and regulation. 4. Ripple and noise is measured from 10KHZ to 20MHz bandwidth at output with parallel 0.1uF ceramic and 22uF electrolytic capacitors.
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797
PSPRL9802D Series
Active PFC 200 Watt Dual Output AC/DC Switching Power Supply MECHANICAL DRAWINGS
Overall Size: 6.8(L) x 3.8(W) x 1.5(H) inches; Weight: 650g.
Output Pin Assignment Howder Molex V1: Pin 1 V1: Pins 1 - 3 V2: Pin 4 V2: Pins 10 - 12 RTN: Pins 2 - 3 RTN: Pins 4 - 9
AC Input Connector (CN1): Mating Molex Part No. 09-91-0500 or equivalent (5pin, 3used) PCB is Labeled: L = Line; N = Neutral; G = Chassis Ground Mating Pins; Molex Engineering Series 2478, 2578, 8818 or Howder Terminal block Part No. FTB-702-3P (3 pin). Output Connector (CN2): Mating Molex Part No. 09-91-1200 (12 pin) or Howder Terminal block Part No. HD-301-4P (4 pin). Output Pin Assignment: (See table above). Logic signal connectors (CN3): Mating JST XHP-5 or equivalent (CHYAO SHIUNN JS-2001-04). Mating Pins: JST SXH-002T-P0.6 for AWG 30 to 26. Fan Drive: Mating JST XHP-2 or equivalent (CHYAO SHIUNN JS-2001-02). Mounting Inserts: 8 Places M4. Maximum Penetration 4mm see outline drawing for location. Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797

▲Up To Search▲

Price & Availability of PSPRL9802D

	To Download PSPRL9802D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .